How do I find Angelo Garcia who used to work for Cleveland Wrecking Co. ?
He lived in Tacoma Wa
Careers & Employment - 1 Answers
People's Answers, Critics, Comments, Opinions :
Answer 1 :
Well you could put up a billboard in the city to see if it gets any responses. You could check with the company he used to work for and ask if they have a forwarding address. Send a letter to him at his last known address and see if it comes back with a forwarding address. Call information. Hope this helps.
Read more other entries :
Thursday, December 16, 2010
Wednesday, December 1, 2010
About My new fuel pump for my 1973 Mustang 351 Cleveland does not work when installed
My new fuel pump for my 1973 Mustang 351 Cleveland does not work when installed?
I''ve installed a new fuel pump in my 351 cleveland but it does not push fuel out (there is fuel at the inlet). I think theres a problem lining up to the camshaft, anyideas?
Maintenance & Repairs - 5 Answers
People's Answers, Critics, Comments, Opinions :
Answer 1 :
Have you tried tapping the engine around a little at a time with the starter and then reinserting the pump lever? Maybe when you removed the old pump, the pump lever happened to be in a bad position.
Answer 2 :
i don't know anything about this but you're hot picture caught my eye. you're a hottie
Answer 3 :
Hi there are a couple of things you need to make sure is right. 1) you have the right fuel pump,I am not being a smart ..... reason being the length of the actuator arm is very important . 2) Was the old fuel pump working all right before you changed it? why was it changed? was it leaking? if the answer is yes to all of the above, then I think you have the wrong pump. 3) Was it fitted propely? you might not have done it right. The best thing to do would be to remove the pump and check and make sure it is the right one to start off with. Good luck...... ASH
Answer 4 :
make sure the arm on the fuel pump is under the cam lobe.if iam not mistaken,they run off the cam lobe instead of a push rod.
Answer 5 :
you need to pull irt back of and see if you bent or broke the pump lever. sounds like it went over the cam sprocket. if i did not then when you put it on try to lift the bottom of it gently then slide it in slowly you will feel the ca this way as it will be hard to lift it in place as there will be a slight pressure on it. when you get it bolted back down it sholuld work. or you can buy a afermarket electric punp.
Read more other entries :
I''ve installed a new fuel pump in my 351 cleveland but it does not push fuel out (there is fuel at the inlet). I think theres a problem lining up to the camshaft, anyideas?
Maintenance & Repairs - 5 Answers
People's Answers, Critics, Comments, Opinions :
Answer 1 :
Have you tried tapping the engine around a little at a time with the starter and then reinserting the pump lever? Maybe when you removed the old pump, the pump lever happened to be in a bad position.
Answer 2 :
i don't know anything about this but you're hot picture caught my eye. you're a hottie
Answer 3 :
Hi there are a couple of things you need to make sure is right. 1) you have the right fuel pump,I am not being a smart ..... reason being the length of the actuator arm is very important . 2) Was the old fuel pump working all right before you changed it? why was it changed? was it leaking? if the answer is yes to all of the above, then I think you have the wrong pump. 3) Was it fitted propely? you might not have done it right. The best thing to do would be to remove the pump and check and make sure it is the right one to start off with. Good luck...... ASH
Answer 4 :
make sure the arm on the fuel pump is under the cam lobe.if iam not mistaken,they run off the cam lobe instead of a push rod.
Answer 5 :
you need to pull irt back of and see if you bent or broke the pump lever. sounds like it went over the cam sprocket. if i did not then when you put it on try to lift the bottom of it gently then slide it in slowly you will feel the ca this way as it will be hard to lift it in place as there will be a slight pressure on it. when you get it bolted back down it sholuld work. or you can buy a afermarket electric punp.
Read more other entries :
Subscribe to:
Posts (Atom)